HayBuster H-1030

The latest introduction to the Haybuster PTO tub grinder family is the H-1030 model.

It also has a 10’ tub and comes equipped with tub tilt and heavy-duty hammermill, that is located in the rear of the tub. It also has a dual-auger system to discharge material efficiently to the hydraulic folding stacking conveyor. The H-1030 requires a minimum of 150 hp up to 315 hp tractor. The newly designed electronic governor protects the tractor and machine from overloads, allowing the tub grinder to grind efficiently and consistently.

44” Heavy Duty Hammermill

The H-1030 is equipped with a 44” (111.76 cm) long heavy-duty hammermill that has been positioned to the rear of the tub. With the mill in the back, the ground product can easily be discharged and transferred to the slacking conveyor. The hammermill is constructed of 3/8” (0.95 cm) thick x 15-3/4 (40 cm) diameter plates with 1-1/4 (3.18 cm) case-hardened rods that hold 64-3/8 (0.95 cm) hammers. These hammers have four hardened edges that can be rotated and flipped to complete many hours of grinding. The mill is mounted to the frame with two 3” (7.62 cm) pillow block bearings on 3-1/2 (8.89 cm) stress-proof shaft. From tip to tip the mill has a 26” (66.04 cm) swing diameter.

8 Belt Drive System

The 8 multiple belt drive systems has been designed to handle increased horsepower and rotor speed. The spring tension belt drive system allows for constant belt tensions while belts stretch and wear without having to manually adjust. Access door allows for tension adjustments or drive maintenance.

Heavy-Duty Mill Grade/Slug Bar Combination

The heavy-duty bolt-in mill grate/slug bar combination is designed to allow the operator the ability to change the number of mill grate bars and slug bars as grinding conditions change. Simply take off or add as necessary. A geyser plate can be added to prevent product from being tossed straight up and out of the tub.

Dual High Capacity Augers

The H-1030 has 12” x 4’ (30.48 cm x 1.22 m) long dual augers for discharging ground product. Augers are mounted with two heavy-duty bearings located at the base of the discharge, allowing free-flowing of product to the stacking conveyor. Expansion of the dischargearea allows for higher capacity and reduces possibility for plugging.

Large Big Bite Tub

The H-1030 has a 10’3” (3.12 m) tub constructed of 10-gauge steel in the floor and 12-gauge steel in the tub. The tub is 44.5” (1.13 m) deep and will handle all types of bales.

ECU 710 Electronic Governor

On the H-1030 the tub rotation feeds the hammermill using a Wachendorf A35 with an ECU 710 Electronic Control Governor. This stabilizes engine load by adjusting the tub speed. It also controls tub direction, clockwise, stop and counter-clockwise.

Tub Drive

The tub drive has continuous teeth around the tub and dual spring tensioners to keep the chain tight. Power is provided by a single hydraulic motor controlled by the electronic governor.

90 Degree Tub Tilt

The H-1030’s tub opens a full 90 degrees for easy access to the hammermill and drive train for daily maintenance and easy screen changing.

24” Wide x 21’ Long High Capacity Stacking Conveyor

The 21’ long x 24” wide (6.4 m x 60.96 cm) hydraulically folding conveyor is designed for the increased capacity of a 10’ tub grinder. The conveyor folds over the top of the tub for easy transport. It is capable of stacking material up to 14’9” (4.5 m) high at a 40 degree angle.

Large 16.5 x 16.1, 14-Ply Flotation Implement Tires

Large 16.5 x 16.1, 14-ply flotation implement tires provide for easy transportation and a solid base for the H-1030.

Optional Grain-Grinding Hopper

Grain Grinding with a Haybuster PTO tub grinder has becomes a very popular use of our hay grinding machines. Installing a grain grinding holler over the hammermill and changing screens will convert H-1030 into a high-capacity grain grinder.

Standard Features

• The H-1030 is equipped with a 44” long heavy duty hammermill that has been positioned to the rear of the tub. With the mill in the back, the ground product can quickly be discharged and transferred to the stacking conveyor. The hammermill is constructed of 3/8” thick plates with 1 ¼” case-hardened rods that hold 64-3/8” hammers. These hammers can be rotated and flipped for many hours of grinding. The mill is mounted to the frame with two 3” pillow block bearings on a 3 ½” stress-proof shaft.
• The 8 multiple belt drive system has been designed to handle increased horsepower and rotor speed. The spring tension belt drive system allows for constant belt tension while belts stretch and wear without having to manually adjust.
• The heavy-duty bolt-in mill grate/slug bar combination is designed to allow the operator the ability to change the number of mill grate bars and slug bars as grinding conditions change. A geyser plate can be added to prevent product from being tossed straight up and out of the tub.
• The H-1030 has 12” diameter x 4’ long dual augers for discharging ground product. Augers are mounted with two heavy-duty bearings located at the base of the discharge, allowing free flow of product to the stacking conveyor. Expansion of the discharge area allows for higher capacity and reduces possibility for plugging.
• The H-1030 has a 10’ 3” wide heavy-duty tub. The tub is 44 ½” deep and will handle all types and sizes of bales.
• On the H-1030, the tub rotation feeds the hammermill using a Wachendorf Electronic Control Governor, which stabilizes engine load by adjusting or stopping the tub speed. It also controls tub direction, clockwise, stop, and counterclockwise as well as tracking grinding hours.
• The tub drive has continuous teeth around the tub and dual spring tensioners to keep the chain tight. Power is provided by a single hydraulic motor controlled by electronic governor.
• The H-1030’s tub opens a full 90 degreees for easy access to the hammermill and drive train for maintenance and service.
• The 21’ long x 24” wide hydraulicallyfolding conveyor is designed for the increased capacity of a 10’ tub grinder. The conveoyor folds over the top of the tub for easy transport. It is capable of stacking material up to 14’ 9” high at a the maximum angle.
• Large flotation implement tires provide for easy transportation and a stable base for the H-1030.
• Grain grinding with a Haybuster PTO tub grinder has become a very popular use of our hay grinding machines. Installing a grain grinding hopper on the hammermill and changing screens will convert the H-1030 into a high-capacity grain grinder.

Optional Features

PTO Shaft -1000 RPM
Tractor Half, 1-3/4 in, 20 Spline Shaft
Tractor Half, 1-3/8 in, 21 Spline Shaft

Geyser Plates
Geyser Plate Kit, use with the Slug Buster
Geyser Plate Kit, slotted, use with the Mill Grate

Hopper for Grain Grinding

Ear Corn Kit
Better diets for dairy cows - an article from the USDA -describes how finely ground grains/corn can offer a better diet for cows.

Closed Center Conversion Kit
This kit is required to operate the conveyor lift valve properly, with John Deere 60 and older series tractors.

Grinding Screens
1/8 in. (3.18 mm) Round Hole Screen Half*
3/16 in. (4.76 mm) Round Hole Screen Half**
1/4 in. (6.35 mm) Round Hole Screen Half
3/8 in. (9.52 mm) Round Hole Screen Half
1/2 in. (12.7 mm) Round Hole Screen Half
5/8 in. (15.88 mm) Round Hole Screen Half
3/4 in. (19.05 mm) Round Hole Screen Half
1 in. (25.4 mm) Round Hole Screen Half
1-1/2 in. (38.1 mm) Round Hole Screen Half
2 in. (50.8 mm) Round Hole Screen Half
3 in. (7.62 cm) Round Hole, Screen Half (standard)
4 in. (10.16 cm) Round Hole, Screen Half (standard)
5 in. (12.70 cm) Round Hole, Screen Half (standard)
6 in. (15.24 cm) Round Hole, Screen Half (standard)
7 in. (17.78 cm) Round Hole, Screen Half (standard)
8 in. (20.32 cm) Round Hole, Screen Half (standard)
Dummy (Open) Screen Half
*1/8 in. (3.18 mm) thick,
**3/16 in. (4.76 mm) thick, all other screens are 1/4 in. (6.35 mm) thick