HayBuster H-1130E

H-1130 Electric Stationary Tub Grinder

The H-1130 Electric tub grinder has all the features of the PTO driven heavy-duty H-1130. It’s powered by two electric motors, a 300 hp motor that drives the hammermill and a 10 hp motor that powers the hydraulics. It is available with a variety of electrical packages.

High Capacity Augers

The new dual 12” x4’6” (30.48 cm x 1.37 m) belly augers are suspended by two heavy-duty bearings and are located at the base of the newly designed screen area. The short dual-augers allow for a sealed under screen discharge area. The larger discharge area also provides for higher capacities and reduces the possibility for plugging.

50” Heavy-Duty Hammermill

The Big Bite 50” (127 cm) heavy-duty hammermill is now standard equipment and has been moved to the rear of the tub to reduce the length of the belly discharge, along with the increased area around and under the screens accelerants product removal and reduces the possibility of plugging. The heavy-duty hammermill operates at 2300 RPM or 40% faster than previous models and is constructed with 88-1/2” (1.27 cm) swinging hammers. The hammers have four hardened working edges that can be rotated to provide a new grinding edge. They are held in place with 1-1/4” (3.18 cm) case-hardened hammer rods. The mill plates are 1/2” (8.98 cm) thick and 16” (40.64 cm) in diameter. The hammermill is mounted on a 3-1/2” (8.98 cm) stress-proof shaft supported by 3-1/4 (8.21 cm) bearings. During operation the swinging hammers extend to a full 26” (66.04 cm).

DuraTech Electronic Governor

The DuraTech model RCB93 electronic governor is the reason for a smooth productive machine. This governor maintains a constant load on the tractor and driveline by adjusting the tubs RPM which controls the feed rate of the materials to the hammermill.

8-5 VP Belt Drive System

The belt drive system for the hammermill has been redesigned with 8-5 VP belts to handle the increased rotor speed, increased horsepower capacity and to allow for changing of belts without removing the bull gear. The spring tension belt drive automatically adjusts belt tension as the belts stretch. Spring tension adjustment can be made through the side access door.

Tub Drive

The tub drive has continuous teeth around the tub and dual spring tensioners. Power is provided by a single hydraulic motor controlled by the electronic governor.

Heavy-Duty Grates/Slug Bar Combination

The new heavy-duty bolt-in mill grate/slug bar combination is designed to allow the operator the ability to change the number of mill grate bars and slug bars as grinding conditions change. Simply take off or add as necessary. A geyser plate can be added to prevent product from being tossed straight up and out of the tub.

Large Big Bite Tub

The large H-1130 Big Bite Tub is constructed of a 10-gauge steel floor and a 12-gauge steel side wall. The width of the tub is 11’3” (3.43 m) at the flare, 8’11” (2.72 m) at the base and is 50” (127 cm) deep. With this large tub the H-1130 has the capacity to handle the largest round and square bales as well as loose hay.

90 Degree Tub Tilt

The electric H-1130’s tub opens a full 90 degrees for easy access to the hammermill and drive train for daily maintenance and easy screen changing.

24” Wide x 26’ Long High Capacity Stacking Conveyor

The new hydraulic folding 24” wide by 26’ long (60.96 cm by 7.92 m) capacity stacking conveyor is designed for the increased capacity of the electric H-1130. A rubber-lagged drive pulley along with Haybuster’s Easy Clean” idler pulley to power the belt. 1-1/2 (3.81 cm) high cleats help haul the ground product away at a high rate without slowing down, even when the hammermill is overloaded. The ground product can be piled up to 18’6” (5.64 m) high with the conveyor.

Large 16.5 x 16.1, 14-Ply Flotation Implement Tires

Large 16.5 x 16.1, 14-ply flotation implement tires provide for easy transportation and a solid base for the electric H-1130.

Optional Grain-Grinding Hopper

High-capacity grain grinding is another important operation that the electric H-1130 can also accomplish. By removing the mill great/slug bar, placing the optional grain-grinding hopper over the hammermill opening and changing screens, the H-1130 becomes a high capacity grain grinder for grinding and/or cracking feed grains.

Soft Start Panel for the Main Drive 300 HP (23.8 kw) Motor

A soft start panel provides for “soft” startup for the main drive 300 HP (23.8 kw) motor. The 10 HP (7.46 kw) motor that drives the hydraulics is a direct line start. Electric motors are available in 460 volt-60 Hz, 380 volt-50 Hz, 380 volt-60 Hz and 575 volt-60 Hz, all require three phase power. Please check with your power supplier for the proper power requirements for your area before ordering.

300 HP (223.8 kx) Motor for Primary Drive and 10 HP (7.46 kw) Motor for Hydraulics

300 HP (223.8 kx) three phase sft start motor for primary drive, 10 HP (7.46 kw) motor for hydraulics (tub, tilt and conveyor lift).

Available Electric Motors:

300 HP (223.8 kw), 380 volt-50 Hz three phase power required
300 HP (223.8 kw), 380 volt-60 Hz, three phase power required
300 HP (223.8 kw), 575 volt-60 Hz, three phase power required
Please check with your power supplier for the proper power requirements for your area.